| Both sides previous revisionPrevious revisionNext revision | Previous revision |
| computing:piholeonblack [2021/03/01 18:26] – oemb1905 | computing:piholeonblack [2023/02/27 01:10] (current) – oemb1905 |
|---|
| chown pihole:pihole /var/lib/misc/dnsmasq.leases | chown pihole:pihole /var/lib/misc/dnsmasq.leases |
| sudo nano /etc/dnsmasq.d/SoftAp0 | sudo nano /etc/dnsmasq.d/SoftAp0 |
| | #interface=usb0 |
| | #interface=usb1 |
| #cache-size=2048 | #cache-size=2048 |
| #dhcp-leasefile=/var/run/dnsmasq.leases | #dhcp-leasefile=/var/run/dnsmasq.leases |
| | |
| sudo apt remove --purge connman | sudo apt remove --purge connman |
| sudo reboot | sudo reboot [OR, if you don't have serial and/or lose connection, unplug and plug back in after 5-10] |
| | |
| More than likely, the Beagle Bone Black will hang at around 20/30% of the removal, since it will have lost its dhcp client reservation. Personally, I always have serial connected just in case, but if not, wait 3-4 minutes and then unplug and plug the device back in, and connman will be removed, and pihole-FTL.service will now be able to start and listen on port 53 and manage DNS requests, and the pihole will configure the device properly as a dhcp client underneath your router. The next step is to configure your router DHCP server to utilize the pihole DNS for its clients. In my case, I use openWRT so I go to Interfaces / LAN / DHCP Server / Advanced Settings. In that area, you can specify what DNS the router should use: | More than likely, the Beagle Bone Black will hang at around 20/30% of the removal, since it will have lost its dhcp client reservation. Personally, I always have serial connected just in case, but if not, wait 5-10 minutes and then unplug and plug the device back in, and connman will be removed, and pihole-FTL.service will now be able to start and listen on port 53 and manage DNS requests, and the pihole will configure the device properly as a dhcp client underneath your router. The next step is to configure your router DHCP server to utilize the pihole DNS for its clients. In my case, I use openWRT so I go to Interfaces / LAN / DHCP Server / Advanced Settings. In that area, you can specify what DNS the router should use: |
| |
| {{ :computing:openwrt.png?direct&600 |}} | {{ :computing:openwrt.png?direct&600 |}} |
| Thanks to [[https://frdmtoplay.com/running-pi-hole-on-the-beagle-bone-black/|Freedom to Play]], [[https://bacnh.com/how-to-setup-pi-hole-with-openwrt/|Embedded Knowledge]], and Jared from [[https://gitlab.com/ABQLUG|ABQ GLUG]] for the idea to tinker with this. | Thanks to [[https://frdmtoplay.com/running-pi-hole-on-the-beagle-bone-black/|Freedom to Play]], [[https://bacnh.com/how-to-setup-pi-hole-with-openwrt/|Embedded Knowledge]], and Jared from [[https://gitlab.com/ABQLUG|ABQ GLUG]] for the idea to tinker with this. |
| | |
| --- //[[jonathan@haacksnetworking.com|oemb1905]] 2021/03/01 11:08// | --- //[[jonathan@haacksnetworking.com|oemb1905]] 2021/10/27 11:17// |
